Industrial telephone

 
DOWNLOAD PDF

ATP-1-3
industrial telephone set - without a keyboard






   

 
DOWNLOAD PDF

ATP3
industrial telephone set

The telephone is designed for application in arduous conditions, such as humidity, noise, dust, mechanical hazards, chemical pollution and areas, where it is essential or advisable to conduct conversation in speakerphone mode without being used handset.

It is recommended for installation in industrial facilities, construction sites, warehouses, guardposts, in non-methane mines, etc. High level of dialing signal and highly visible led indicators ensure the effectiveness of the telephone, even in toughest conditions. The telephone meets dust-proof and splash-proof requirements according to the protection degree IP-54. The telephone can connected to any kind of CB telephone exchange ( voltage 60V, 50V or 24V). It is suitable to be mounted in vertical position on flat surface.

 
DOWNLOAD PDF

ATP-3-6
industrial telephone set - without a keyboard 

 DOWNLOAD PDF  

APD                      
double-line industrial

The APD double-line industrial telephone set is the terminal that makes it possible to have calls over 2 independent telephone lines and can be coupled with any CB telephone exchange. It is designed for being used wherever there are difficult working conditions, e.g. very high humidity, noise, dustiness, mechanical exposures, polluted atmosphere. It is recommended for installation at industrial halls, guardrooms, construction sites, warehouses and non-methane mines etc.
High level of call signal volume and very intensive optical signaller visible from a far distance ensure efficient calling even in environments with high noise level and high dustiness degree.

The telephone casing provides dust- and splash-proofness with IP65 grade of protection.
The telephone set is designed for operation within the temperature range of -25°C to 60°C.

 
DOWNLOAD PDF

ATP-GM
industrial speakerphone

The industrial speakerphone is designed for being used wherever there are difficult working conditions, e.g. very high humidity, noise, dustiness, mechanical exposures, and chemical pollution of atmosphere, and at the same time the handset mode without use of microtelephone is required or recommended for the calls. It is recommended for installation at industrial halls, guardrooms, construction sites, warehouses etc.
High level of call signal volume and very intensive light signalisation ensure efficient calling in very noisy or heavily dusted environments.
The telephone’s construction provides dust- and waterproofness with IP 54 grade of protection.

DOWNLOAD PDF 

ATGI-IIB
intrinsically safe telephone set

The ATGI-IIB intrinsically safe telephone set is intended for operation at sites where dangerous explosion mixtures of flammable gases and vapours with air occur under normal operating conditions – explosion group II, category 2G, subgroup B, temperature class T4. The telephone’s construction provides for operation under difficult operating conditions (noise, mechanical exposures, dustiness, high humidity). High level of call signal and very intensive optical signaller visible from a far distance provide efficient call even in places with very high noise level and high dustiness degree. The ATGI-IIB telephone set is certified by the European notified laboratory (FTZU 05 ATEX 234X) for the II 2G EEx IIB T4 feature. It can operate with any automatic telephone exchange through the AUI-1-IIB or AUI-2-IIB Intrinsically Safe Subscriber System or the other manufacturers’ intrinsically safe separation systems including input circuits with the II G EEx ia IIB feature.

   

DOWNLOAD PDF

KSI
intrinsically safe separation unit  

The unit contains DC/DC converter providing the required voltages of 48VDC and 12VDC converted from the unit’s supply voltage of 48VDC, which is absorbed from the PBX’s buffer power supply. In the unit, the AUI-1-IIB intrinsically safe barrier systems are installed in the amount from 1 to 6, according to the order.

DOWNLOAD PDF

AUI-1-IIB
sparkproof barrier

Application:
These devices ensure intrinsically safe separation at sites where dangerous explosion mixtures of flammable gases and vapours with air occur under normal operating conditions – explosion group II, category (1)G, subgroup B.

The device supports 1 intrinsically safe telephone set only!
The essence of operation of this device is galvanic separation between the telephone line’s circuit from the PBX side and the intrinsically safe part of the line, i.e. the cable circuit and intrinsically safe telephone located within the explosible area. In addition, the device brings a number of limitations and protections so that the intrinsically safe telephone is powered by safe voltage.

DOWNLOAD PDF

GRAFIT
workshop telephone

The Grafit workshop telephone set is the analogue telephone that may be connected to telephone exchanges of any type. It is intended first of all for using at sites where there is a hazard of mechanical damages, pollutions, noise, limited humidity – e.g. at factory halls, craftsmen’s workshops, warehouses etc.

AD-1
telephone set

AD-1 telephone set is designed for use as a terminal to receive call signals and answer the incoming calls, without possibility of dialling phone numbers.
It can be coupled with any CB telephone exchange and dispatch equipment with supply voltage of 60V, 50V or 24V).

DOWNLOAD PDF

AGM
telephone speakerphone

Telephone set designed for being used in environments where making and receiving calls in handset mode only is recommended.
It is equipped with a reinforced plastic casing and front metal-plate board. The telephone’s construction provides dust- and waterproofness with IP 65 grade of protection.
The set is equipped with a selection keyboard with large membrane keys in distinctive colours so that it can be easily operated even with gloves on. The additional 4 keys allow the most often used numbers to be dialled quickly.
The telephone’s construction allows its surface to be kept clean easily. The set is resistant to most disinfectants.
It can be coupled with any CB telephone exchange operated in either tone or pulse mode. It is designed for operation in vertical position, with possibility of mounting to flat surfaces (e.g. wall).
The AGM speakerphone is particularly recommended for use in environments with increased humidity and dustiness and wherever enhanced cleanliness is required and devices are subject to treatment with disinfectants.

PS - 5
signalling attachment

The PS-5 signalling attachment is a device connected to the telephone line parallel with the telephone set to detect the calling signal and switch on the additional signalling elements, such as lamps, buzzers etc, using high-current relay contacts.
The attachment has an aesthetic hermetic casing with cable glands used as the input and output wire outlet.
The casing ensures dust- and hose-proofness with IP 65 grade of protection so it can be installed in open and exposed spaces.
The attachment is suitable for being connected a number of supply voltages and can be set in two operating modes: while ringing and continuous.